Individální projekty MPOA

Tato stránka je pouze pro čtení. Můžete si pouze prohlédnout zdrojový kód, ale ne ho měnit. Zeptejte se správce, pokud si myslíte, že něco není v pořádku.
**This is not the final version**

====== Project Goals ======
 
  * Design hardware part of heating regulator to control three heating elements (2kW ~230V each)
  * Design homebrewing control unit which will take care of:
    * Temperature measuring
    * Temperature PID regulation
    * Stirring control
    * Character display GUI controlled by buttons
    * RTC
    * Basic cooking program functionality
  * Create own C drivers (display, RTC, ...)

====== Regulator HW ======

===== Principle =====

Regulator acts as power switch driven by low-frequency PWM signal from MCU. For safety and lucidity purposes, regulator will be placed at separate PCB, its interface to MCU will consist of logic supply pins and single trigger pin for each driven phase.

==== Switching component ====

Power triac was chosen as sufficient switch component in terms of power/price efficiency. Any triac allowing >12A continual working current (incl. 3A margin) would be acceptable (BTA12-600B - TO220 ~0.8$), however these packages do not provide insulation to common terminal (case). This problem would require additional electric insulation between the package and the heatsink, in cost of worsening thermal insulation. In case of common heatsink to all 3 triacs (3 phases), the peak voltage will reach over 500V peak. This lead to use of BTA26B/600V - TOP3 ~3.6$ as one of the cheapest available triacs with insulated package.

==== Logic ====

Optotriac provides considerable solution for direct drive of power triac, together with ensuring galvanic isolation of power and logic part. MOC3031 is optotriac with builtin logic providing zero-cross switching, which decreases power loss on power triac and significantly reduces EMI.


==== Scheme ====

{{ :2015:schema.png?500 |}}

==== PCB ====

{{ :2015:msbrew_pcb.png?500 |}}

====== MCU ======

MSP430G2553 from TI was chosen as the MCU for this project. MSP430 family are 16-bit RISC microcontrollers aimed at simplicity and extremely low  power consumption. MSP430G2553 (in PDIP-20) has 10 bit ADC unit, common interface peripherals (I2C, SPI, UART) and two 16-bit timers with 3 capture/compare units.

===== Temperature Control =====

==== Temperature Measurement ====

Currently tested temperature measuring is based on direct measure of output voltage of LM35 - precision centigrade temperature sensor from TI, packaged in TO92. Its output voltage gets increased by 10mV per 1°C rise. Sensor is loaded with 1k pulldown resistor and connected directly to ADC input. 

If this package proves to be unsuitable for microbrewery needs, LM35 will be replaced with PT100 temperature sensor packaged in stainless steel capsule, which will lead to small changes in temperature calculations (temp. calculated by reading from table). Hardware is designed to be suitable for both methods.

=== ADC ===

ADC circuitry is clocked from SMCLK/8 with internal reference (1.5V). Noise is reduced by use of sample and hold at 2kHz. ADC is triggered from timer interrupt and its value is further filtered with exponetial window.
Detailed information about ADC settings are obvious from ADC init procedure (vid. init.c)

''inline void init_ADC()''

<code c>
  void __attribute__ ((interrupt(ADC10_VECTOR))) ADC_ISR (void)
  {
    temp_current = (ALPHA * ADC10MEM) + (1.0 - ALPHA) * temp_current;
  }
</code>


==== PID regulator ====

Proportional - Integral - Diferential (PID) regulator is used for driving of output unit (motors, heaters, ...) based on input values (rpm, temperature). Output value consists of sum of P, I and D parts. Proportional contribution is difference of current value and required value, integral contribution is accumulator of all previous and current errors and differential contribution represents the difference (trend) of current and previous error at measured time. To ensure required functionality, all three contributions must be weighted by coefficients, depending on system. PID is implemented in ''getPID()'' function:

<code c>
#define KP   24
#define KI   0.2
#define KD   60

uint8_t getPID(float set_point, float measured_value){
  float actual_error, P, D;
  static float error_previous;
  static float I;

  actual_error = set_point - measured_value;
  // PID
  P  = actual_error;   //Current error
  I += error_previous;  //Sum of previous errors
  D  = actual_error - error_previous;  //Difference with previous error

  error_previous = actual_error;

  float result = KP*P + KI*I + KD*D;

  if(result > 254)
    result = 255;

  if(result < 0)
    result = 0;

return result;  
}
</code>

While the output of PID regulator is directly driving the 8bit PWM controller, output value must be limited to fit ''uint8_t'' borders.

==== Output control ====

Phase outputs will be driven by custom low frequency PWM signal. This PWM is needed to be done by hand, because hadware PWM can not run on low frequencies. In this project, each output (phase) has its own uint8 register (Phase Duty Counter PDC) which is being incremented in intervals given by Timer A CC0 unit (and is repeatedly overflowing).Those registers are representing progress within uint8 Global Duty Cycle register. At each CC0 interrupt, PDCs are compared with global duty cycle register and appropriate output pins are set or reset.

<code c>
// TACC0
void __attribute__ ((interrupt(TIMER0_A0_VECTOR))) Timer_A_ISR (void)
{
  static uint8_t ptr1 = 0;
  static uint8_t ptr2 = HEATER_MARGIN;
  static uint8_t ptr3 = 2 * HEATER_MARGIN;

    // TACCR0 interval : 50Hz
    TACCR0 += 2500;

    if(ptr1 < g_duty)
      P1OUT |= BIT0;
    else
      P1OUT &= ~BIT0;

    if(ptr2 < g_duty)
      P1OUT |= BIT2;
    else
      P1OUT &= ~BIT2;

    if(ptr3 < g_duty) {
      P1OUT |= BIT3;
    }else{
      P1OUT &= ~BIT3;
    }

    ptr1++;
    ptr2++;
    ptr3++;
}
</code>

While PDCs are static and affected only by periodical increments, those can be preset differently. If so, outputs are ensured not to be switched on or off at the same time. If loads are powered from single phase, this will significantly reduce peak switching current (same principle as time relays) and thus EMI. The delay between triggering particular outputs is called **Phase Margin** and is obvious from figure below:

{{ :2015:msbrew_pwm.png?direct&600 |}}


===== Stir control =====

Stir constrol means putting single output pin to logical "1" or "0" by hand or at predefined time intervals.

===== Display interface =====

Character display module with 4x20 characters was chosen as display unit. This display module contains HD44780 display driver with 8b/4b paralel interface. 

These functions are currently provided (hd44780.h):
<code c>
void display_init();
void display_clear();
void display_return_home();
void display_goXY(uint8_t x, uint8_t y);
void display_print_char(const char character);
void display_print(const char *text);
</code>

==== RTC ====

Embeded module with DS3231 RTC chip was used as RTC source. This module is connected via I2C interface to MCU, contains temperature-compensated crystal, battery and additional 32k EEPROM memory. This chip can also serve as time generator and can act as an alarm (raising pin at desired time), however none of these functions are used in this project. At this time, RTC chip will serve only as a clock source.

Setting and reading time is done simply by reading or writing appropriate register on RTC chip. Time values are stored in BCD, a small calculation is thus needed before writing or after reading to display the value.

DS3231 driver currently provides these functions (ds3231.h):
<code c>
uint8_t rtc_get_seconds();
uint8_t rtc_set_seconds(uint8_t seconds);
uint8_t rtc_get_minutes();
uint8_t rtc_set_minutes(uint8_t minutes);
uint8_t rtc_get_hours();
uint8_t rtc_set_hours(uint8_t hours);
</code>

=== Programming ===

====== Conclusion ======

This project uses newlib, the c library for embedded systems. At first, sprintf() from previously mentioned library was used for string handling, however, this function at its own consumed over 5kB of program memory which is totally unacceptable and must be replaced by custom simplified implementation.
Individální projekty MPOA

Uživatelské nástroje

Nástroje pro tento web

Nástroje pro stránku
